Citroën Xantia

since 1993 release

Repair and operation of the car

Removal and installation of seat belts

Try to remember adjusting provisions of various washers and remote plugs used in anchor knots of fastening of belts.

Seat belts of front seats

Removal

PERFORMANCE ORDER

1. Having accurately hooked, remove the decorative panel from the outer edge of a front seat. Delay the panel forward, then give it to a door and remove from a seat. 2. Turn out a bolt of fastening of the lower anchor of a belt to a seat frame.
3. Having hooked, uncover the top anchor bolt of a belt on the central body rack.
4. In the lower part of the central rack turn out two screws of fastening of the panel of its finishing. Pull together sealing strips from edges of the panel, then remove the panel from a rack.
5. Turn out a fixing bolt and remove the top anchor assembly of a belt from a rack.
6. Turn out a bolt of fastening of an inertial drum of the returnable device and remove assembly of a seat belt from the car.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs of anchor knots and durability of tightening of fixture.

Stem holders of buckles of forward seat belts (model without natyazhitel of belts)

Removal

PERFORMANCE ORDER

1. Turn out fixing screws / release clamps and remove the side panel of finishing of a seat.
2. The holder fastens a bolt to a seat frame. Under a head of a bolt the washer is enclosed (do not forget about it).

Installation

Installation is made upside-down. Track durability of tightening of fixture.

Stem holders of buckles of forward seat belts (model with natyazhitel of belts)

On the models equipped with system of a pretightness of forward seat belts it is necessary to perform small preparatory work:
   a) Take the ignition key;
   b) Disconnect a negative wire from the battery and wait about 10 minutes;
   c) Disunite the contact socket of an electrical wiring of the device of a pretightness (sockets are painted in orange color and are located under seats).

Do not make attempts of diagnosing of blocks of a pretightness of belts. Remember that giving of any power supply (including the current developed by the internal power supply of an ohmmeter) leads to operation of mechanisms of the device of a pretightness. Besides, operation of devices happens also at a warming up of assemblies up to the temperature above 100 °C.

Removal

PERFORMANCE ORDER

1. The holder is built in the mechanism of a natyazhitel of a seat belt. 2. Turn out fixing screws / release holders and remove the side panel of finishing of a seat. 3. Release an electrical wiring of a natyazhitel from clamps on the lower party of a seat.
4. Weaken the forward screw of fastening of a natyazhitel. 5. Turn out a back fixing bolt. A — the Forward screw B — the Back bolt
6. Remove the mechanism of a natyazhitel from a seat.

Try not to touch with hands a buckle or a cable, - you hold a natyazhitel for the case.

Installation

Installation is made upside-down. Pay attention to the next moments:
a) Before installation of a natyazhitel make sure that the rechargeable battery is disconnected, and ignition is switched off;
b) Try not to touch a seat belt buckle at the first inclusion of ignition.

Side seat belts of a back seat

Removal

PERFORMANCE ORDER

1. Open a door of a back and a back door of the car from the relevant party of the car. Remove sealing strips in edges of the panel of internal finishing of back side section of a body.
2. Hooking the panel of internal finishing of a back rack release it from clamps and remove (pay attention that the panel is latched in persistent section of the back shelf).
3. Turn out a bolt of fastening of the top anchor knot of a seat belt to a back rack. 4. Put a seat pillow for the purpose of ensuring access to the lower anchor bolt of a belt forward. Turn out a bolt.
5. Having hooked, release facing of a window under a seat belt from the side panel of internal finishing of salon, then miss the top and lower anchor knots of a belt through the panel.
6. Otboltite an inertial drum of the returnable device also remove assembly of a seat belt from the car.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs of anchor knots and durability of tightening of fixture.

Central seat belt of a back seat

Removal

PERFORMANCE ORDER

1. Assembly just of a pribolchen to the car floor panel, - lift a seat pillow.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs of anchor knots and durability of tightening of fixture.

Electronic control unit of natyazhitel of forward seat belts

Removal

The block is located under the central console.

PERFORMANCE ORDER

1. Disconnect a negative wire from the battery and wait not less than 10 minutes. 2. Remove the central console (see Removal and installation of the central console). 3. Disunite contact sockets of an electrical wiring. Try to remember routes of laying of plaits.
4. Give four fixing nuts and remove the control unit from a basic arm.

Installation

Installation is made upside-down. Track correctness of laying of an electrical wiring and reliability of fastening of contact sockets before connecting the rechargeable battery.

On the homepage