Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and finishing of salon
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and the accompanying components
   Windshield, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   Exterior body finish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal and installation of door rear-view mirrors and the accompanying components

Mirrors with the manual drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (see Removal and installation of panels of an internal upholstery of doors).
2. Separate and unbend the top forward corner of the plastic sealing screen of a door for the purpose of ensuring access to the plug of a driving cable through passage of the regulator of provision of a mirror. Take the plug from the door panel.
3. Having hooked, release the panel of decorative finishing from a door corner, at the corresponding complete set release from clamps on the panel the sensor of tracking of the anticreeping alarm system, then remove the panel.
4. Turn out five fixing screws and remove assembly of a rear-view mirror from a door. Pass a driving cable through an opening throughout doors. Try to remember a route of laying of a cable.

Installation

Installation is made upside-down. Track correctness of laying of a driving cable.

Mirrors with the electric drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (see Removal and installation of panels of an internal upholstery of doors).

2. Find the ends of a spring clamp of fastening of the glass located from the upper edge of assembly of a mirror. Where it is required, remove the control unit of the window regulator electric drive with a block of the contact socket for the purpose of ensuring access.

3. Take the rubber plug of an electrical wiring through passage from the door panel.

4. Having hooked, release the panel of decorative finishing of knot of fastening of a mirror from a door corner. At the corresponding complete set release the sensor of tracking of the anticreeping alarm system from the panel, then remove the panel.

5. Walk on an electrical wiring plait from a mirror to a block and disunite contact sockets. At the corresponding complete set disconnect also an electrical wiring of the temperature sensor.

6. Turn out five fixing screws and remove assembly of a mirror from a door. Release an electrical wiring plait from a door.





Installation

Installation is made upside-down. Track correctness of laying and reliability of fastening of an electrical wiring.

Mirror glass

Removal

 PERFORMANCE ORDER

1. Glass fastens in assembly of a mirror by means of a metal spring clamp.
2. Find the ends of a clamp of fastening of the glass located from the upper edge of assembly of a mirror. Where it is required, remove the control unit of the window regulator electric drive with a block of the contact socket for the purpose of ensuring access.

3. Hook the ends of a clamp the screw-driver for the purpose of mirror glass release.

4. Remove glass, at the corresponding complete set disconnect an electrical wiring. Remove a spring clamp if it is put freely from assembly.
A — Contact sockets of an electrical wiring
B — the Spring clamp

Installation

 PERFORMANCE ORDER

1. Establish a spring clamp on the back party of glass of a mirror. Track that the ends of a clamp correctly entered glass grooves.
2. Fill glass in assembly of a mirror to a clamp zashchelkivaniye in an adjusting flute.

For simplification of landing of a clamp previously slightly grease a plastic ring on the regulator.

Switch of control of the electric drive of adjustment of provision of a door mirror

See the Head Onboard electric equipment.

On the homepage