Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and finishing of salon
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and the accompanying components
   Windshield, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   Exterior body finish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment
+ Schemes of electric equipment


04d84ca1



Removal and installation of panels of an internal upholstery of doors

Forward doors

Removal

 PERFORMANCE ORDER

1. Open a door and approximately on two thirds lower a windowpane. Disconnect a negative wire from the battery.

2. Extend the button of switching off of the lock, then by means of the small screw-driver wring out a lock uvula and finally remove the button.

3. On models with the manual drive of window regulators remove the handle of management from the spindle, then remove a facing plate.

4. Turn out the screw located in the lower back end of facing of the internal handle of a door.

5. Having accurately hooked, remove the facing panel from the handle. At the corresponding complete set, delay the panel of an internal upholstery from a doorframe and disunite contact sockets of an electrical wiring of the drive of a window regulator / a door rear-view mirror. If door mirrors are equipped with the manual drive, remove decorative finishing of the driving mechanism from the panel of an internal upholstery.

6. Turn out two lower screws of fastening of an armrest.

7. Through an opening in the door handle turn out the top screw of fastening of an armrest (pay attention that the internal handle is a part of a design of an armrest).

8. Turn out the screw of fastening of the panel of an internal upholstery, located from the forward party of an opening of the internal handle.

9. Having accurately hooked the screw-driver, remove the loudspeaker cover panel.

10. Turn out three screws of fastening of the panel of an internal upholstery located around the loudspeaker loudspeaker.

11. Hooking the suitable bifurcate tool, release the clamps located on perimeter of a door and remove the panel of an internal upholstery (do not forget to disconnect an electrical wiring from a loudspeaker).

12. If there is a need for removal of the plastic sealing screen, it is necessary to dismantle previously the internal handle (see Removal and installation of door handles and components of the lock) and, at the corresponding complete set, the control unit of the window regulator electric drive:
   a) The control unit of the electric drive of a window regulator fastens two screws used also for fixing of a block of contact sockets of an electrical wiring. Disconnect an electrical wiring, then turn out screws and remove the block;
   b) Release contact sockets from a block and remove the last;
   c) On the models equipped with the anticreeping alarm system disunite the contact socket of an electrical wiring of the sensor of tracking (the sensor is built in in the decorative panel of finishing of a door mirror).

13. Accurately separate the sealing screen from a doorframe (if the screen is not replaced, try not to damage a film). At removal of the screen pass electrical wiring plaits through openings through passage in it.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down. Pay attention to the next moments:
   a) Replace the fixing clamps damaged in the course of dismantle of the panel of an internal upholstery;

   b) Make sure that the coupling screw of an executive rod of the door lock after installation of the internal handle was tightened;

   c) At installation of the button of switching off of the lock at first close a door and make sure that the executive rod of the switch is in the lower situation. Translate a lock uvula in lower of two openings, then densely put the button for the end of a rod (before click), - the lock uvula at the same time has to appear in the top opening.

Back doors

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a door.
3. Perform the procedures described in the subsection "Forward Doors — Removal", subitem 2 — 11.
4. In need of removal of the plastic sealing screen at first release fastening clamps on a door of a basic arm of an electrical wiring.

Installation

See the subsection "Forward Doors — Installation".


On the homepage