Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and finishing of salon
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and the accompanying components
   Windshield, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   Exterior body finish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal, installation and adjustment of a door of a back and its telescopic emphasis

Back door

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a back door.
3. Open hatches of access and disconnect an electrical wiring from the combined lamps which are built in at a door back.
4. Release clamps and turn out fixing screws and remove the lower panel of an internal upholstery of a door of a back.
5. Release clamps of fastening of an emphasis of the back shelf on panels of a side upholstery of a door of a back (beat out the central pins, then take clamps). Remove an emphasis.

6. Turn out fixing screws and remove side panels from a back door.

7. Disconnect an electrical wiring from the consumers of the electric power located in a door (including contact sockets on both sides of a heater of back glass). If the door is not replaced, tie up string pieces to electrical wiring plaits.
8. Accurately disconnect a hose of supply of liquid of washing of back glass from a nozzle on assembly of an electric motor of a screen wiper. Prepare for collecting the spilled liquid. Release a hose from a door at the top together with an electrical wiring plait.
9. Take rubber plugs of an electrical wiring through passage from the top end face of a door, then release plaits of wires from a door. Leave the tied-up string pieces sticking out of openings through passage.
10. Ask the assistant to take a door and serially release spring clamps of both telescopic emphasis. Release spherical hinges of an emphasis from reception nests on doors.

11. Screw fixing bolts and by means of the assistant remove a back door from the car. Transfer a door to the safe place.

Installation and adjustment

 PERFORMANCE ORDER

1. By means of the assistant get a door on the regular place, screw and tighten fixing bolts.

2. Further installation is made as it should be, the return to a dismantle order. Pay attention to the next moments:
   a) Gas station at a door of plaits of an electrical wiring is made by means of left passed through openings of pieces through passage of a string;

   b) After installation of a door check uniformity of its arrangement of rather adjacent body panels. In case of need release adjusting bolts and make the corresponding adjustment. Having achieved satisfactory result, do not forget to tighten adjusting screws;

   c) Having adjusted the provision of a door, check serviceability of functioning of its locks. In case of need weaken fixing bolts (it is necessary to remove the back panel of finishing of a door - see Removal and installation of components of the lock of a door of a back) and as appropriate correct position of locks.

Telescopic emphasis

Removal

 PERFORMANCE ORDER

1. Prop up a back door in open situation.

2. By means of the screw-driver with a flat sting release a spring clamp of a spherical support of a telescopic emphasis on doors.

3. Take a clamp from a support.

4. Repeat the procedure, having released the hinge since the opposite end of an emphasis. Remove an emphasis from the car.

Installation

Installation is made upside-down. Track reliability of a zashchelkivaniye of clamps.

On the homepage