Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and finishing of salon
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and the accompanying components
   Windshield, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   Exterior body finish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal and installation of seats

Front seats

On the models equipped with system of a pretightness of forward seat belts it is necessary to perform small preparatory work:
   a) Take the ignition key;
   b) Disconnect a negative wire from the battery and wait about 10 minutes;
   c) Disunite the contact socket of an electrical wiring of the device of a pretightness (sockets are painted in orange color and are located under seats).

Do not make attempts of diagnosing of blocks of a pretightness of belts. Remember that giving of any power supply (including the current developed by the internal power supply of an ohmmeter) to natyazhitel leads to operation of their mechanisms. Besides, operation of natyazhitel happens also at a warming up of assemblies up to the temperature above 100 °C.


Rassoyedineniye of the contact socket of an electrical wiring of a natyazhitel of a forward seat belt

The seat is for descriptive reasons removed.

Removal

 PERFORMANCE ORDER

1. Accurately remove the plastic decorative panel from the outer edge of a seat. At first the panel should be delayed forward, then to shift towards a door for the purpose of release from clamps.

2. Turn out the lower anchor bolt of fastening of a seat belt to a seat frame.

3. Shift a seat against the stop forward for the purpose of ensuring access to back fixing bolts. Turn out bolts.

4. Now shift a seat back and turn out forward bolts of its fastening.
5. On the models equipped with the electric drive of adjustment of provision of seats before dismantle it is necessary to make sure that the rechargeable battery is switched-off.
6. At the corresponding complete set disunite the contact socket(s) of the electrical wiring laid under a seat.
7. Remove a seat and take it from interior of the car.
8. Remove plastic floor boards (try to remember their adjusting situation).

Installation

Installation is made upside-down.

Pillow of a back seat (seat of a continuous design)

Removal

 PERFORMANCE ORDER

1. Lift a first line of a pillow and incline it forward.
2. Remove decorative covers from seat loops.
3. Give nuts of fastening of a pillow to loopy assemblies, then take a pillow from interior of the car.

Installation

Installation is made upside-down.

Back of a back seat (seat of a continuous design)

Removal

 PERFORMANCE ORDER

1. Release a clamp and put a back forward.
2. Turn out screws of fastening of a back to the loopy assemblies located in the opposite ends of a seat. Lift a back and take it from interior of the car.

Installation

Installation is made upside-down.

Pillows of a back seat (seat of a separate design)

 PERFORMANCE ORDER

1. Perform procedures of the subsection "Pillow of a Back Seat (Seat of a Continuous Design) — Removal". For the purpose of ensuring access to nuts of fastening of loopy assemblies it is necessary to remove decorative covers from them.

Backs of a back seat (seat of separate type)

Removal

 PERFORMANCE ORDER

1. Release a clamp and put a seatback forward.
2. Turn out fastening screws to a floor of the loopy assemblies located on both sides of a seatback. Pay attention that at removal of a back of a smaller seat it is enough to turn out fastening screws to a floor only of an external loop.
3. Lift a back and take it from interior of the car. At removal of a back of a smaller seat its inner edge should be released from a loopy level.

Installation

Installation is made upside-down.

On the homepage