Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and finishing of salon
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and the accompanying components
   Windshield, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   Exterior body finish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment
+ Schemes of electric equipment


04d84ca1



Removal and installation of components of the lock of a door of a back

Assembly of the lock

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a back door
3. Open hatches of access and disconnect an electrical wiring from assemblies of the back combined lamps which are built in at a door.

4. Remove clamps.
Above — Extraction of the central pin of a clamp
Below — Extraction of a clamp of fastening of the finishing panel of a door of a back



5. Turn out fixing screws.

6. Remove the lower panel of finishing of a door of a back.

7. Mark the provision of heads of bolts of fastening of castle assembly.

8. Turn out two fixing bolts and remove assembly of the lock, having disconnected from it an executive rod.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Track correctness of installation of fixing bolts (according to the tags put in the course of dismantle);
   b) Before installation to the place of the finishing panel make sure of serviceability of functioning of the lock. In case of need weaken fixing bolts and as appropriate correct the provision of assembly. Having finished adjustment, strongly tighten fixing bolts and install into place the finishing panel.

Lock cylinder

Removal

 PERFORMANCE ORDER

1. Perform the procedures described in the subsection "Assembly of the Lock — Removal", subitem 1 — 4.
2. At the corresponding complete set screw two fixing bolts and remove the block of the activator of the uniform lock. Having removed the servo-driver, disconnect an executive rod and an electrical wiring from the lock.

3. Turn out three fixing screws, take sideways the lock cylinder from a door and disconnect the remained executive rod.

4. For extraction of the cylinder from assembly remove a foam sealing ring, then insert a key into a keyhole and at the same time release a lock uvula of fastening of the cylinder. For a key take the cylinder.

Installation

Installation is made upside-down. Track for correctness of installation and reliability of fastening of an executive rod.

Lock drummer

Removal

 PERFORMANCE ORDER

1. Uncover and turn out screws of fastening of the back panel of an upholstery of the luggage compartment. Remove the panel, having provided thereby access to the lock drummer.

2. Unbend edge of a carpet back and turn out two bolts of fastening of the drummer. At the corresponding complete set release the sensor switch of the anticreeping alarm system from assembly of the drummer.

Installation

Installation is made upside-down.


On the homepage