Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
- Onboard electric equipment
   Search of causes of failures of electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm fixtures
   Replacement of lamps of internal lighting fixtures
   Removal and installation of external lighting and alarm fixtures
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation of the lighter
   The alarm system "do not forget to switch off lighting fixtures" - the general information
   Removal and installation of a horn of a horn
   Removal and installation of a driving cable of the speedometer/sensor of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of an electric motor and drafts of the drive of screenwash
   Removal and installation of an electric motor of the drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and installation of the radio tape recorder
   Removal and installation of loudspeakers
   Removal and installation of the antenna of the radio receiver
   Anticreeping system - the general information
   Safety cushion - the general information, precautionary measures and deactivation of system
   Removal and installation of components of a safety cushion
   Diagnostics of systems of electronic control
+ Schemes of electric equipment


e94432e4



Removal and installation of external lighting and alarm fixtures

Before starting removal of lighting fixtures, do not forget to disconnect a negative wire from the battery.

Head block headlights

Removal

 PERFORMANCE ORDER

1. Remove the forward index of turn from the corresponding board of the car (see below) and a forward lattice (address the Head Kuzov and finishing of salon).
2. Turn out two top fixing screws and one lower.

3. Remove assembly of a block headlight from the car (the top bolts are shown by shooters).



4. Disconnect the electrical wiring brought to assembly.

5. In case of need the lens can be removed from a headlight:
   a) Accurately hooking the screw-driver, release clamps of fastening of edges of a lens. At assembly clamps are subject to replacement without fail;

   b) Carefully remove a lens from a block headlight. Try not to touch with fingers a reflector mirror surface;
   c) Remove and will throw out sealing laying;
   d) Clean an adjusting flute in a casing of a block headlight and put in it new sealing laying;

   e) Put on ledges at the edges of a lens new fixing clamps, then press a lens to a casing of assembly of a block headlight and in strictly certain order latch clamps.

Installation

Installation is made upside-down. At the first opportunity make check / correction of installation of optical axes of block headlights.

Forward indexes of turns

Removal

 PERFORMANCE ORDER

1. Open a cowl.

2. From the inside of a wing release a fixing clamp and push out outside assembly of the index of turn (the arrow showed a fixing clamp).



3. Disconnect an electrical wiring and remove assembly of the index from the car.

Installation

Installation is made upside-down. Track reliability of a zashchelkivaniye of a clamp.

Side repeaters of forward indexes of turn

Removal

 PERFORMANCE ORDER

1. Shift assembly of the repeater forward and release it from the body panel of the car.
2. Disconnect an electrical wiring and remove assembly of the repeater.

Installation

Installation is made upside-down.

Forward fog lights

Removal

 PERFORMANCE ORDER

1. Pull facing of assembly of a fog light before the click confirming an otpuskaniye of clamps forward.

2. Push the screw-driver in the top corner of an air vent in a spoiler and wring out a clamp of fastening of assembly of a fog light.

3. Having pulled on itself, release assembly of a fog light from the landing nest (the arrow showed a fixing clamp).

4. Disconnect it from a spoiler (the arrow showed a lock uvula).

5. Disconnect an electrical wiring and remove assembly of a fog light from the car.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down. Before filling assembly in a spoiler, make sure that its facing is shifted in the forward (released) situation. First of all fill the lock uvula located from the outer edge of a headlight in a spoiler.
2. Having put assembly aflush with a spoiler surface, fix it by a clamp.

Adjustment

Adjustment of an optical axis of a fog light is made by means of the special screw located from the inside of assembly. The screw turns the screw-driver with a crosswise sting which should be passed throughout the central groove in a spoiler.

The combined lamps which are built in at a back door back

Removal

 PERFORMANCE ORDER

1. Open a back door.
2. Release a clamp and remove a folding cover from the back party of lantern assembly.
3. Disconnect an electrical wiring from a back part of a lamp holder, then release two fixing clamps and remove a lamp holder.

4. Having hooked the screw-driver, release an internal clamp.

5. Then pull lantern assembly outside and release two remained external clamps.

Installation

Installation is made upside-down.

The combined lamps which are built in in wings back

Removal

 PERFORMANCE ORDER

1. In the luggage compartment of the car give a fixing nut and remove assembly of the back combined lamp from a wing.

Installation

Installation is made upside-down.

Lamps of illumination of registration plate

Removal

 PERFORMANCE ORDER

1. Having accurately hooked the screw-driver, release assembly of a lamp of illumination of registration plate from the back door panel.
2. Disconnect an electrical wiring and remove assembly of a lamp from the car.

Installation

Installation is made upside-down.

On the homepage