Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
- Onboard electric equipment
   Search of causes of failures of electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm fixtures
   Replacement of lamps of internal lighting fixtures
   Removal and installation of external lighting and alarm fixtures
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation of the lighter
   The alarm system "do not forget to switch off lighting fixtures" - the general information
   Removal and installation of a horn of a horn
   Removal and installation of a driving cable of the speedometer/sensor of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of an electric motor and drafts of the drive of screenwash
   Removal and installation of an electric motor of the drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and installation of the radio tape recorder
   Removal and installation of loudspeakers
   Removal and installation of the antenna of the radio receiver
   Anticreeping system - the general information
   Safety cushion - the general information, precautionary measures and deactivation of system
   Removal and installation of components of a safety cushion
   Diagnostics of systems of electronic control
+ Schemes of electric equipment


e94432e4



Replacement of lamps of internal lighting fixtures

General information

See Replacement of lamps of external lighting and alarm fixtures, the subsection "General Information".

Saloon lamps, mate lamps and illumination of a motive compartment

 PERFORMANCE ORDER

1. Having hooked the screw-driver, release the lamp from a casing for the purpose of ensuring access to a lamp.

2. Turn a cartridge counterclockwise and take it together with a lamp.

3. The lamp has press landing in the boss.
4. Installation is made upside-down.

Illumination of a ware box

 PERFORMANCE ORDER

1. Open a cover of a ware box, release lock and a uvula and completely cast away a cover.

2. Having hooked, release the lamp from the top plane of a ware box.

3. Turn a cartridge counterclockwise and take it from the lamp together with a lamp.

4. The lamp has press landing in the boss.

5. Replace a lamp and install into place the lamp.

Lamps of illumination of switches

Lamps of illumination are built in assemblies of switches and in an individual order are not delivered.

Lamps of illumination of the control panel of functioning of a heater

 PERFORMANCE ORDER

1. Extend an ashtray from the dashboard.
2. Turn out two fixing screws, then, hooking the small screw-driver, accurately release clamps and remove facing of control panels of functioning of the radio tape recorder and a heater.
3. On the models equipped with the ware shelf in the central part of the dashboard turn out four fixing screws and remove the shelf.
4. Turn out two fixing screws and take assembly of the radio tape recorder from the dashboard. Disconnect an electrical wiring and an antenna cable from a back part of assembly.
5. Turn out four fixing screws and release a radio tape recorder casing from the dashboard. Where it is required, release from clamps on a casing an electrical wiring and an antenna cable.
6. Uncover assembly of the control panel of functioning of a heater.

7. Release the holder of lamps of illumination from a back part of the panel.

8. Lamps have press landing in the holder.
9. Replace the failed lamp and install components on the regular places. Act as it should be, the return to a dismantle order.

Lamp of illumination of hours

 PERFORMANCE ORDER

1. Take from the dashboard assembly of the central ventilating nozzle for the purpose of ensuring access by o'clock (see Removal and installation of hours).

2. In a back part of hours turn a cartridge of a lamp counterclockwise and take it from assembly.

3. The lamp is built in a cartridge.
4. Replace a lamp and install components into place.

Lighter/ashtray illumination lamp

 PERFORMANCE ORDER

1. Extend an ashtray from the dashboard.
2. Turn out two lower fixing screws and completely remove assembly of an ashtray from the dashboard.
3. Having pulled outside, release a cartridge of a lamp from a back part of assembly of an ashtray, disconnect an electrical wiring.
4. The lamp has press landing in the boss.
5. Replace a lamp and install into place components. Act as it should be, the return to a dismantle order.

Control lamps and lamps of illumination of an instrument guard

 PERFORMANCE ORDER

1. Remove an instrument guard (see Removal and installation of an instrument guard).

2. Turn a cartridge of a lamp counterclockwise and take it from a back part of a guard.

3. All lamps are built in the cartridges and are replaced assembled with it.
4. Replace the failed assembly and install components on the regular places. Act as it should be, the return to a dismantle order.


On the homepage