Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
- Repair of the engine
   - The repair procedures which are not demanding extraction of the engine from the car - petrol engines
      Check of compression pressure in cylinders
      Fixing cranked / distributive shaft for the purpose of prevention of service of the car, casual in the course of performing procedures
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a bent shaft
      Removal and installation of covers of a gas-distributing belt
      GRM drive belt - the general information, removal and installation
      Removal, check of a state and installation of a natyazhitel and cogwheels of a gas-distributing belt
      Replacement of an epiploon(s) of the camshaft
      Removal, check of a state and installation of the camshaft and pushers of valves
      Check and adjustment of valvate gaps
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a state and installation of the oil pump
      Removal and installation of the oil cooler (model of 2.0 l)
      Replacement of epiploons of a bent shaft
      Removal, check of a state and installation of a flywheel / driving disk
      Check of a state and replacement of support of a suspension bracket of the power unit
   + The repair procedures which are not demanding extraction of the engine from the car - diesel engines
   + Removal and capital repairs of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Replacement of epiploons of a bent shaft

Right epiploon

 PERFORMANCE ORDER

1. Remove a cogwheel of a bent shaft and (at the corresponding complete set) the remote plug (see Removal, check of a state and installation of a natyazhitel and cogwheels of a gas-distributing belt). Take a gas-distributing belt aside from a working zone and fix it in order to avoid pollution by oil there. Measure and write down the adjusting depth of landing of an epiploon in the casing.

2. Puncture, or drill couple of small openings in a face surface of an epiploon and screw in them self-tapping screws. Grasp heads of screws with nippers and take an epiploon from the nest in a casing. Alternatively the epiploon can be taken by a poddevaniye by the screw-driver with a flat sting - try not to damage walls of a nest and persistent coat hanger on a shaft pin.

3. Clear a casing of an epiploon and carefully remove from walls of a nest and a pin of a shaft all roughnesses and teases capable to lead to failure of a new epiploon.
4. Oil sponges of a new epiploon pure motive, then accurately put on it a pin of a bent shaft (sponges inside). Try not to damage soft sponges of an epiploon at putting on it on a pin.
5. By means of a suitable mandrel (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (see item 1).
6. Collect by rags excess of oil and establish into place a cogwheel of a bent shaft (see Removal, check of a state and installation of a natyazhitel and cogwheels of a gas-distributing belt).

Left epiploon

 PERFORMANCE ORDER

1. Remove a flywheel / a driving disk (see Removal, check of a state and installation of a flywheel / a driving disk). Measure and write down the adjusting depth of landing of an epiploon in the casing.
2. Puncture, or drill couple of small openings in a face surface of an epiploon and screw in them self-tapping screws. Grasp heads of screws with nippers and take an epiploon from the nest in a casing.
3. Clear a casing of an epiploon and carefully remove from walls of a nest and a pin of a shaft all roughnesses and teases capable to lead to failure of a new epiploon.
4. Oil sponges of a new epiploon pure motive, then accurately put on it a pin of a bent shaft (sponges inside). Try not to damage soft sponges of an epiploon at putting on it on a pin.
5. By means of a suitable mandrel (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (see item 1).
6. Collect by rags excess of oil and establish into place a flywheel / a driving disk (see Removal, check of a state and installation of a flywheel / a driving disk).


On the homepage