Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, capital repairs and installation of the lower lever of a forward suspension bracket
   Removal and installation of the lower spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proofreader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proofreader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, capital repairs and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   The angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal and installation of a stretcher of a forward suspension bracket

Removal

The divider of spherical support will be required. Everything самоконтрящиеся nuts at assembly are subject to replacement without fail.


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see the Head Uniform hydraulic system).
2. The car also establish to Poddomkratta it on props. Remove forward wheels.
3. Under the car remove a protective cover from a nut of the cranked lever of the drive of gear shifting, give a nut and disconnect draft of switching from the rotary support on a stretcher.

4. Turn out fastening boats to a stretcher of the mechanism of rack steering transfer, remove remote plugs. A wire tie up assembly of the steering mechanism to system of production of the fulfilled gases.

5. Give a nut and take a bolt of fastening of an arm of a back support of the power unit to the rubber pillow.

6. On both sides of the car turn out bolts of fastening of loker of wheel arches to a stretcher.
7. Serially weaken and partially turn off nuts of fingers of both lower spherical support, then divide support by means of the special tool. After release of spherical fingers finally remove nuts from their shafts.
8. Working in the same manner, by means of a divider of spherical support serially disconnect racks of the stabilizer of cross stability from the ends of its bar. At an otdavaniye of nuts the finger of a rack can be held from a provorachivaniye by means of a prutkovy key on 5.0 mm.
9. From the left board of the car weaken and partially turn off a nut of a spherical finger of fastening of a tip of steering thirst for stupichny assembly. Release a finger from the landing nest by means of a divider of spherical support, then finally remove a nut.

10. In the right back corner of a stretcher turn out two bolts and release a clamp of fastening of a guide of lines of communication (wires and hydraulic tubes). For an otpuskaniye of a clamp beat out its central pin.

11. On the models equipped with a hydroactive suspension bracket disconnect an electrical wiring from the sensor of movements of a body.

12. Turn out two bolts of fastening of valvate assembly of the proofreader of a road gleam to a stretcher.

13. Weaken a coupling bolt and disconnect an executive rod of manual correction of a road gleam from the proofreader.

14. Disconnect hydraulic tubes from the proofreader's valve. At once to a zakuporta the open ends of lines and reception ports of the valve in order to avoid hit in system of dirt.

15. Turn out three bolts of fastening of basic arms of lines of communication in the left back corner of a stretcher.

16. Take a fastening clamp on a stretcher of a guide of lines of communication. For an otpuskaniye of a clamp beat out its central pin.

17. Disconnect tips of cables of the drive of the parking brake from executive levers of supports of brake mechanisms. Release covers of cables from the bearing ledges on supports. Take assemblies of cables aside.
18. Since both ends of a stretcher release hydraulic tubes from basic arms (separate flexible hoses from tubes, then release tubes from intermediate clamps on a stretcher) (address the Head the Brake system).
19. Turn a steering wheel against the stop to the left.
20. Attentively examine a stretcher and release from clamps on it all remained lines of communication (wires, hydraulic tubes and hoses (perhaps, it is necessary to make a detachment of some lines). Try to remember routes of laying of all wires, hoses and tubes. At a rassoyedineniye of nipple sockets be ready to collecting the spilled liquid. At once cork the open ends of tubes/hoses and unions of their connection for the purpose of minimization of losses of hydraulic liquid and in order to avoid hit in system of dirt.
21. Prop up a stretcher a cart jack through wooden whetstone.

22. Turn out six fixing bolts and slightly lower a stretcher on a jack.



23. Last time make sure that no communication tenches prevent removal of a stretcher.
24. Finally lower a stretcher and take it from under the car.
25. At desire the lower levers and a bar of the stabilizer of cross stability can be removed from a stretcher (see appropriate sections).

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Where it is required, install on a stretcher the lower levers and a bar of the stabilizer of cross stability of a suspension bracket according to the instructions provided in the sections Removal, capital repairs and installation of the lower lever of a forward suspension bracket and Removal and installation of components of the stabilizer of cross stability of a forward suspension bracket. Pay attention that final tightening of fixture has to be made only after installation of a stretcher on the car;
   b) At the corresponding complete set do not forget to replace sealing elements of nipple connections of hydraulic lines;
   c) Remember that everything самоконтрящиеся nuts are subject to replacement without fail;
   d) Track correctness of laying and reliability of fastening of all lines of communication;
   e) Do not forget to check correctness of adjustment of the parking brake (address the Head the Brake system);
   f) After lowering of the car on the earth tighten spuskny the gate of the regulator of pressure and transfer a control lever a suspension bracket to situation "Maximum";
   g) Check the level of hydraulic liquid, in case of need make the corresponding adjustment (address the Head Routine maintenance);
   h) Do not forget to pump over hydraulic system (address the Head the Brake system);
   i) In conclusion, make adjustment of height of a road gleam according to the instructions provided in the section Check of Installation and Adjustment of a Road Gleam then tighten coupling bolts of collars of fastening of the proofreader of a road gleam and (at the corresponding complete set) the sensor of movements of a body.

On the homepage