Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, capital repairs and installation of the lower lever of a forward suspension bracket
   Removal and installation of the lower spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proofreader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proofreader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, capital repairs and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   The angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal and installation of longitudinal levers of a back suspension bracket

Removal

The new nut of an axis of the rotary lever will be required.


 PERFORMANCE ORDER

1. Prop up antiretractable boots forward wheels and cock the parking brake, then a back of the car and establish to a poddomkratta it on props. Remove the corresponding back wheel.
2. Remove the corresponding hydraulic block of a back suspension bracket (see Removal and installation of hydraulic blocks of a back suspension bracket).

3. On the equipped ABS models perform the following procedures:
   a) Turn out three fixing screws and remove a brake board;
   b) Turn out a fixing bolt and remove the wheel ABS sensor. Shift the sensor aside, watching that its electrical wiring was not tense;
   c) Remove the thermofilter of the wheel sensor.

4. Release the nipple socket and disconnect a hydraulic tube from a brake support. At once to a zakuporta the open ends of a tube and the union of its connection in order to avoid hit in system of dirt.
5. Release hydraulic tubes from intermediate clamps on the longitudinal lever and assembly of the back bridge.
6. Get a jack under the longitudinal lever located from an opposite board of the car and cock it so that the lever was parallel to the earth.

7. Turn out two bolts of fastening to the longitudinal lever of a bar of the stabilizer of cross stability which is subject to removal. Pay attention that one of bolts is used also for fastening of a basic arm of a hydraulic tube.

8. Give a nut of an axis of the rotary lever.

9. Get wooden whetstone between a bar of the stabilizer of cross stability and a body of the car, then use it as the lever for assignment of a bar from a body. Try not to allow tension of the hydraulic tubes fixed in arms over the end of a bar of the stabilizer.
10. Take an axis of the longitudinal lever, then remove the lever from the car.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Before installation the axis of the longitudinal lever should be greased on all length;
   b) Do not forget to replace a lever axis nut. Track respect for efforts of tightening of fixture;
   c) The description of the procedure of installation of the hydraulic block is provided in the section Removal and installation of hydraulic blocks of a back suspension bracket;
   d) In conclusion do not forget to pump over hydraulic system (address the Head the Brake system).

On the homepage