Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, capital repairs and installation of the lower lever of a forward suspension bracket
   Removal and installation of the lower spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proofreader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proofreader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, capital repairs and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   The angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


04d84ca1



Removal and installation of tips of steering drafts

Removal

New nuts of spherical fingers will be required.


 PERFORMANCE ORDER

1. Prop up back wheels of the car, then a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel.
2. Weaken and partially turn off a nut of a spherical finger of fastening of a tip of steering draft on stupichny assembly, then release a finger from a reception nest by means of a divider of spherical support. Remove a nut.
3. If the tip is used further, mark its situation to a draft bar.
4. Record a draft bar from a provorachivaniye and give half way a lock-nut.
5. Having precisely counted quantity of turnovers of a carving, turn out and remove its tip from draft.
6. Count and write down quantity of naked rounds of a carving from an end face of the spherical hinge of a tip to a lock-nut. Check serviceability of a condition of a tip, its protective cover, shaft and carving of a spherical finger. In case of identification of the hinge of a side play or mechanical damages indicating wear make replacement.
7. Carefully clean a carving on a draft bar.

Installation

 PERFORMANCE ORDER

1. At installation of a new tip transfer to it an old lock-nut, having screwed it so that that the quantity of naked rounds of a carving corresponded to the value recorded in the course of dismantle.
2. Screw a tip in draft on the quantity of turns counted in the course of dismantle. At the same time the lock-nut of a tip has to be remote from an emphasis on a quarter of a turn (be verified with the marking put earlier).
3. Fix a tip in stupichny assembly and screw a new nut of a spherical finger, having tightened it with the required effort.
4. Establish a wheel, then lower the car on the earth and tighten wheel bolts with the required effort.
5. Check the angles of installation of forward wheels (see the Angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels), then strongly tighten a lock-nut of a tip of steering draft.



On the homepage