Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, capital repairs and installation of the lower lever of a forward suspension bracket
   Removal and installation of the lower spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proofreader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proofreader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, capital repairs and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   The angles of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal and installation of hydraulic blocks of a back suspension bracket

The otvorachivaniye from the hydraulic block of a spherical receiver requires a tape key. At installation of a receiver new sealing laying will be required. Worn-out sealing elements of nipple sockets of hydraulic tubes are also subject to replacement.


Components of the hydraulic block of a back suspension bracket

And — the Tube of supply of hydraulic liquid
In — the Spherical receiver
With — the Spring clamp of fastening of a connecting bar of a suspension bracket
D — the Spring clamp of fastening of the hydraulic block


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see the Head Uniform hydraulic system).
2. The car also establish to Poddomkratta it on props. Remove the corresponding back wheel.
3. Start under spuskny pressure regulator gate suitable drain capacity. By push-up up of the longitudinal lever of a suspension bracket extort the greatest possible amount of liquid from the hydraulic block.
4. By means of a tape key weaken landing of a spherical receiver, then turn out it from assembly of the hydraulic block.
5. Disconnect a liquid supply tube from the hydraulic block. At once to a zakuporta the open ends of a tube and the nipple socket in order to avoid hit in system of dirt.
6. Remove a spring clamp from a connecting bar of a suspension bracket (see an illustration Components of the hydraulic block of a back suspension bracket).
7. Remove a spring clamp of fastening of the hydraulic block.
8. Remove the hydraulic block from assembly of the back bridge and disconnect from it returnable hydraulic and ventilating tubes.

Installation

 PERFORMANCE ORDER

1. Connect returnable and ventilating tubes to the hydraulic block and start assembly on the regular place. Track that tubes were not jammed.
2. Fix the hydraulic block by a spring clamp.
3. Establish into place a clamp of a connecting bar of a suspension bracket.
4. Connect a liquid supply tube to the hydraulic block. At the corresponding complete set replace a sealing element of the nipple socket.
5. Grease a contact surface of a spherical receiver and install it on the hydraulic block (do not forget to replace sealing laying).
6. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with the required effort.
7. Tighten spuskny the gate of the hydraulic regulator of pressure and transfer a control lever a suspension bracket to situation "Maximum".
8. Start the engine and examine all disconnected and being removed components on existence of signs of leaks.
9. Check the level of hydraulic liquid, in case of need make the corresponding adjustment (address the Head Routine maintenance).


On the homepage