Citroën Xantia

since 1993 release

Repair and operation of the car


Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
- Brake system
   Pumping of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of the brake system
   Replacement of blocks of disk brake mechanisms of forward wheels
   Replacement of blocks of disk brake mechanisms of back wheels
   Check of a state, removal and installation of brake disks
   Removal, capital repairs and installation of supports of disk brake mechanisms of forward wheels
   Removal, capital repairs and installation of supports of disk brake mechanisms of back wheels
   Removal, capital repairs and installation of the valve of management
   Removal and installation of a pedal of a foot brake
   The parking brake - general information and adjustments
   Removal and installation of a control lever of the parking brake
   Removal and installation of cables of the drive of the parking brake
   Removal and installation of the sensor switch of stoplights
   System of anti-blocking of brakes (ABS) - the general information
   Removal and installation of components of system of anti-blocking of brakes
+ Running gear and steering
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment

04d84ca1


Removal, capital repairs and installation of supports of disk brake mechanisms of back wheels

See the preventions provided in the section the Brake system. At assembly new sealing washers of the nipple socket of a hydraulic tube will be required.


Details of fixture of a support of the back brake mechanism

Pay attention that before removal the support has to be fastened by a finger of fastening of blocks

1 — the Hydraulic tube
2 — Bolts of fastening of a support
3 — the Finger of fastening of blocks
3 — the Nut of a fixing finger


Components of the brake mechanism of a back wheel

1 — the Brake board and the filter of blocks
2 — the Piston with cuffs
3 — the Finger of fastening of brake shoes
4 — Antivizgovaya a spring
5 — the Brake shoe (internal)
6 — the Support of the brake mechanism
7 — the Brake disk

Removal

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Remove the corresponding wheel.
3. Dump pressure in hydraulic system for what weaken spuskny the regulator gate (see the Head Uniform hydraulic system) and transfer a control lever a suspension bracket to situation "Minimum".
4. Remove brake shoes (see Replacement of blocks of disk brake mechanisms of back wheels).
5. Fasten among themselves two half of a support, having established into place a bolt of fastening of blocks and having strongly tightened its nut.
6. Get drain capacity under the connection union to a support of a hydraulic tube. Release the nipple socket and disconnect a tube from a support. At once to a zakuporta the open ends of a tube and the union for the purpose of minimization of losses of hydraulic liquid and in order to avoid hit in system of dirt.
7. Turn out two fixing bolts and remove assembly of a support (see an illustration of the Detail of fixture of a support of the back brake mechanism).

Capital repairs

Performance of recovery repair of the failed support is possible only with application of a company remnabor of the Citroyon company. Track that the remnabor corresponded to type of the support removed from the car. Pay attention to correctness of installation of each of components. And a sealant before installation grease new laying with hydraulic liquid. For the rest follow instructions of manufacturers. The design of the brake mechanism is presented on an illustration Components of the brake mechanism of a back wheel.

Installation

 PERFORMANCE ORDER

1. Grease a carving of fixing bolts, then establish a support on the regular place, screw bolts and tighten them with the required effort.
2. Connect a hydraulic tube to a support (do not forget to replace sealing washers). Strongly tighten the nipple socket.
3. Give a nut and take a finger of fastening of blocks from a support.
4. Establish into place brake shoes (see Replacement of blocks of disk brake mechanisms of back wheels).
5. Establish a wheel.
6. Tighten spuskny pressure regulator gate (see the Head Uniform hydraulic system) and transfer a control lever a suspension bracket to situation "Normal driving" (The normal movement).
7. Lower the car on the earth and tighten wheel bolts with the required effort.



On the homepage