Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
- Routine maintenance
   + Weekly checks
   + Routine maintenance of the car - petrol models
   - Routine maintenance of the car - diesel models
      Regular service
      Replacement of motive oil and oil filter
      Check of a condition of hoses, and identification of sources of leaks
      Removal of water from the fuel filter
      Coupling adjustment check
      Check of the ATF level
      Suspension bracket and drive of steering
      Check of a condition of protective covers of power shafts
      Reading of memory of the block of self-diagnostics
      Replacement of the dust removal filter (model with To/in)
      Check of a condition of coolant of the air conditioning system
      Check and adjustment of turns of idling and prevention of a spontaneous stop of the engine
      Check of serviceability of functioning of systems of decrease in toxicity of the fulfilled gases
      Check of a state and replacement of a belt of the drive of auxiliary units
      Greasing of the mechanism of the drive of switching off of coupling
      Check of serviceability of functioning and adjustment of the parking brake
      Trial runs
      Replacement of the fuel filter
      Replacement of the AT transmission liquid
      Check of a condition of blocks of brake mechanisms of forward and back wheels
      Greasing of locks and loops
      Replacement of hydraulic LHM liquid and returnable filter
      Replacement of the filtering air cleaner element
      Check of level of gearbox oil (model with RKPP)
      Check of a condition of brake supports, disks and hydraulic hoses
      Replacement of a belt of the GRM drive
      Replacement of cooling liquid
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Replacement of the AT transmission liquid

THROUGH EACH 30 000 KM (18 000 MILES) OF THE RUN

 PERFORMANCE ORDER

1. Make a short trip during which transmission has to be heated-up up to the normal working temperature on the car.
2. Park the car on the flat horizontal platform, whenever possible with a hard coating. Switch off ignition and cock the parking brake. For the purpose of ensuring access prop up antiretractable boots back wheels, then a front of the car and establish to a poddomkratta it on props. For check and adjustment of the ATF level the car has to be again transferred to horizontal position.

3. Take the measuring probe and get the drain capacity suitable on volume under transmission. The case of transmission is equipped with two drain stoppers: one is screwed in the pallet, the second - in the lower part of a case of differential.

Remember that the merged liquid is warmed up to very essential temperature - take precautionary measures against a scalding!

4. Turn out both drain stoppers and lower all contents of a case of transmission in the prepared capacity. Wipe drain traffic jams, with special care having removed metal sawdust from a magnetic insert. Without fail replace sealing washers.
5. After the liquid effluence from transmission stops, smooth out a carving of drain traffic jams and openings in a case. Screw and strongly tighten traffic jams, previously without having forgotten to supply them with new sealing washers. Return the car to horizontal position.
6. Gas station in transmission of fresh ATF is made in the small portions through the directing tube of the measuring probe. Use the funnel equipped with a close-meshed grid. You watch that in a case of AT no foreign objects got. Before adding the next portion of liquid wait some time sufficient for distribution by already filled in ATF in cavities between internal components of a box. Every time check liquid level
7. After the ATF level reaches point MOVE in a probe edge, establish the last on the regular place. Start the engine and let's it work on single turns within several minutes. Again kill the engine and repeat check of the ATF level, in case of need make the corresponding adjustment. Make on the car a short trip for the purpose of final distribution of liquid on internal cavities of the transmission. Repeat check (see the Suspension bracket and the drive of steering).


On the homepage