Citroën Xantia

1. Prop up antiretractable boots back wheels, then a front of the car and establish to a poddomkratta it on props. Transfer the selector lever to situation N.
2. Remove the battery with the pallet and a basic plate (see the Head Elektrooborudovaniye of the engine).
3. Remove the thermofilter(s) of system of production of the fulfilled gases for the purpose of ensuring access to the basis of assembly of the lever of the selector of transfers (see the Head of the Power supply system and release). On some models it is necessary to remove also inlet air duct(s) (see the Head of the Power supply system and release).
4. Since the end of a driving cable turned to transmission turn out two screws of fastening of a cover of a cable to its basic arm. Accurately disconnect a cable tip from the spherical hinge of the lever of the choice of transfers.

Do not allow change of position of the lever of the choice after a detachment from it a driving cable! As an additional precautionary measure mark a starting position of the lever concerning a transmission case.

5. Moving along a cable back, release it from intermediate clamps. Try to remember a route of laying of a cable properly.
6. In interior of the car having accurately hooked, remove the panel of facing of the lever of the selector of transfers from the central console (address the Head Kuzov and finishing of salon).
7. Turn out screws of fastening of the handle on a lever rod. Squeeze out a clamp rychazhok, turn the handle under 90 ° counterclockwise, lift assembly up, then turn under 90 ° clockwise for the purpose of release of the button of a clamp from an executive rod of the lever. After removal of the handle take from it the clamp button with a spring.
8. Give four nuts of fastening of assembly of the lever to a floor.
9. Under the car disconnect assembly of the lever from the body panel and remove it from the car, remembering a route of laying of a cable.
10. Having laid assembly of the lever on a workbench, separate a protective cover from the lever basis and shift it along a cable.
11. Weaken a nut of fastening of a cover of a cable, then remove a fixing clamp. Having accurately hooked, disconnect a cable tip from the spherical hinge in the selector lever basis.
12. Attentively examine assembly of a cable on existence of signs of damage of a cover and wipe of the core. Check serviceability of functioning of a cable: the core has to move freely in a cover. Remember that after installation in regular situation, a cable functions with a much bigger resistance. In case of identification of the slightest signs of malfunction replace assembly.

1. Slightly grease with lubricant on the basis of a molybdenum disulfide open sites of the core of a cable, spherical hinges of levers and the fixing lever mechanism.
2. Pass a cable throughout a selector lever casing. Track, the cable cover flange the openings got on reciprocal ledges of a casing. Fix a cable by a clamp, track that the external ends of the last correctly entered gearing with reciprocal grooves in a lever casing while the internal ends were hooked for the casing basis. Tighten a fixing nut of a cover of a cable.
3. Strongly record a core tip on the spherical hinge of the lever. Return to regular situation on the basis of the lever a protective cover.
4. Having tracked correctness of laying of a cable, start the lever from below on the regular place.
5. Involve assembly of the lever in salon and tighten four fixing nuts.
6. Install the button and a spring of a clamp in the lever handle. Completely drown the button in the handle. Holding the button of drowned, put on the handle a rod of the lever and, having slightly pressed, turn on 90 ° clockwise, then back for the purpose of input of the button of a clamp in gearing with an executive rod. Release the button, then screw and tighten four fixing screws.
7. Under the car, moving along a cable, fix it in all provided intermediate clamps and guides. Place an assembly bracket of a cover of a cable on a basic arm on AT case, screw and tighten fixing bolts.
8. Make sure that levers of the selector and the choice of transfers are in situation N, adjust a driving cable and connect it to the choice lever on transmission (see subitem 4 — 6 in the section Adjustment of a Driving Cable of the choice of transfers of AT).
9. Install into place the thermofilter(s) of system of production of the fulfilled gases (see the Head of the Power supply system and release), then lower the car on the earth.
10. Establish all the other, being removed for the purpose of ensuring access components.