Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
- Power supply system and release
   + A power supply system - petrol models
   - A power supply system - diesel models
      Filling of a power supply system with fuel and removal from it air traffic jams
      Check and adjustment of the maximum turns of the engine
      Removal, installation and adjustment of the thermosensitive RPM meter of bystry idling
      The electromagnetic locking valve - general information, removal and installation
      Removal and TNVD installation
      Methods of check of installation of the moments of injection of fuel
      Check and adjustment of the moments of injection (TNVD Lucas)
      Check and adjustment of the moments of injection (TNVD Bosch)
      Check of serviceability of functioning, removal and installation of nozzles of injection of fuel
      Removal, installation and adjustment of a cable of gas
      Removal and installation of the accelerator pedal
      Removal and installation of assembly of a toplivozabornik with fuel consumption sensor
      Removal and installation of the fuel tank
      Removal and installation of the inlet pipeline and final collector
      Turbocompressor - general information and precautionary measures
      Removal and installation of a turbocompressor
      Check of a state and recovery repair of a turbocompressor
      Removal and installation of the built-in cooler of a turbocompressor
      Removal and installation of the air cleaner and the accompanying components
   + Systems of decrease in toxicity and production of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


04d84ca1



Removal and installation of a turbocompressor


Arrangement of a turbocompressor and the accompanying components

1 — the Branch pipe for connection of an air sleeve
2 — an air supply Sleeve
3 — the Arm of fastening of a maslopodayushchy tube

4 — Maslopodayushchaya a tube
5 — the Collar of fastening of a maslovozvratny tube to the hose connected to the block of cylinders
6 — the turbocompressor Case

Removal

 PERFORMANCE ORDER

1. Remove the inlet pipeline (see Removal and installation of the inlet pipeline and a final collector). Appearance of a turbocompressor and an arrangement of the accompanying components see on the illustration Arrangement of a Turbocompressor and the Accompanying Components.

2. Give a cap nut of nipple connection and disconnect a maslopodayushchy tube from the top part of assembly of a turbocompressor.

3. Cock the parking brake, then a front of the car and establish to a poddomkratta it on props.
4. Disconnect from a turbocompressor a reception pipe of system of production of the fulfilled gases (see Systems of decrease in toxicity and production of the fulfilled gases).

5. Working under the car, release fixing collars and remove the hose connecting a maslovozvratny tube of a turbocompressor to the branch pipe connected to the block of cylinders.

6. Turn out the screw of fastening of a maslopodayushchy tube to a basic arm on the back party of the block of cylinders.

7. Release a cap nut of nipple connection of a maslopodayushchy tube on the block of cylinders and pick up the phone from the engine.



8. Take the filter from nipple knot of a maslopodayushchy tube (from outside the block of cylinders). Estimate extent of pollution of the filter, in case of need clean or replace.

9. Working under the car, turn out two lower bolts of fastening of a turbocompressor.

10. Prop up assembly of a turbocompressor, then turn out the top bolt of its fastening and remove the remote plug.

11. Carefully take assembly of a turbocompressor from a motive compartment (at the top). If assembly is subject to further use, carefully a zakuporta all openings in it in order to avoid dirt hit.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) If replacement of a turbocompressor is made, do not forget to replace also motive oil and an oil filter. Replace also the filter installed in a maslopodayushchy tube;
   b) Do not tighten cap nuts of nipple connections of a maslopodayushchy tube until both of its ends are connected. When tightening a nipple nut of a maslovozvratny tube track that the returnable hose did not stretch;
   c) Before primary start of the engine make filling of an oil contour of a turbocompressor for what disconnect an electrical wiring from the electromagnetic locking valve on TNVD and turn the engine a starter (1-second inclusions) three times.


On the homepage