Citroën Xantia

since 1993 release

Repair and operation of the car



Citroën Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
- Power supply system and release
   - A power supply system - petrol models
      Removal and installation of assembly of the air cleaner
      Removal, installation and adjustment of a cable of gas
      Removal and installation of the accelerator pedal
      Unleaded fuel - the general information and rules of use
      Systems of injection of fuel - the general information
      Dropping pressure in a power supply system
      Removal and installation of the fuel pump
      Removal and installation of the sensor of fuel consumption
      Removal and installation of the fuel tank
      Check of a state and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of the Bosch Motronic 5.1 system
      Removal and installation of components of the Magneti-Marelli 8P system
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + A power supply system - diesel models
   + Systems of decrease in toxicity and production of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and finishing of salon
+ Onboard electric equipment
+ Schemes of electric equipment


e94432e4



Removal, installation and adjustment of a cable of gas

Removal


Knot of fastening of a cable of gas to the throttle case (to model with RKPP)


Knot of fastening of a cable of gas to the throttle case (to model with AT)

 PERFORMANCE ORDER

1. In a motive compartment disconnect the gas cable core from the throttle case, extend a cable from the rubber plug of an arm through passage and remove a spring clamp (see the illustrations Knot of Fastening of a Cable of Gas to the throttle case (to model from RKPP) and Knot of fastening of a cable of gas to the throttle case (to model with AT)).
2. Moving back lengthways on a cable, release it from intermediate guides of clamps and bindings. Try to remember a route of laying of a cable.
3. Release clamps and remove section of the lower felt finishing under the dashboard from the driver's party of the car.
4. In interior of the car release a clamp of a cover of the assembly block of safety locks, having turned it on a quarter of a turn counterclockwise. Uncover the assembly block the dashboard.
5. Release a clip and disconnect the cable core from the top part of the accelerator pedal.
6. Release a cable cover from the holder on a pedal arm. Tie up a string piece by the end of a cable.
7. Return to a motive compartment and release the rubber plug of a cable through passage from a back partition. Then, having pulled a cable on itself, involve it in a motive compartment. Untie a string from a tip and leave it passed through a partition.
8. Attentively examine a cable, checking it for existence of signs of wear or mechanical damages. Also check a condition of the rubber plug through passage. Replace defective components.

Installation

 PERFORMANCE ORDER

1. Tie up a cable to a string and involve it through a partition in interior of the car. Untie a string from a tip and latch a cable cover in the holder of an arm. Connect the core to the end of a pedal.
2. Check reliability of fastening of a cable and landing in a partition of the rubber plug through passage. Install into place the felt panel of finishing of the dashboard and a cover of the assembly block of safety locks.
3. Having returned to a motive compartment, make sure of correctness of landing of a cover of a cable in the plug through passage, then, moving along a cable and watching correctness of a route of laying, fix it in all intermediate clamps and bindings.
4. Put on a flat washer a tip of a cable and establish a spring clamp.
5. Pass a cable cover throughout the plug of an arm through passage on the throttle case. Connect the core of a cable to a cam of the drive of a butterfly valve. Make adjustment of a cable (see below).

Adjustment

 PERFORMANCE ORDER

1. In a motive compartment remove a spring clamp from a gas cable cover. Make sure that the cam of the drive of the gate is pressed to an emphasis. Smoothly pull a cable from the plug through passage, having completely chosen a core weak point.
2. Having recorded a cable in this situation, establish a spring clamp in the last from open flutes in front of the rubber plug through passage. After installation of a clip and an otpuskaniye of a cover, the weak point of the core of a cable has to be very insignificant.
3. Ask the assistant to squeeze out the accelerator pedal and make sure that the cam of the drive passes into the extreme situation corresponding to full opening of the gate. At a pedal otpuskaniye the cam has to come back smoothly to a starting position, nestling on an emphasis.
4. On models with AT, having finished with a gas cable, check adjustment of a driving cable of inclusion of the kick-down mode (see. Automatic transmission).


On the homepage