Citroën Xantia

1. Remove assembly of the dashboard (address the Head Kuzov and finishing of salon).
2. Having released clamps, uncover the top part of the control panel.
3. Release srezny clamps of fastening of cables of management and disconnect tips of cables from control unit levers.

4. Disconnect an electrical wiring from the control unit and lamps of illumination of the panel.

1. Turn out two lower fixing screws, then having accurately hooked the small screw-driver, release clamps and remove facing of the control panel of functioning of a radio receiver/heater.
2. On the models equipped with the ware shelf in the central part of the dashboard turn out four fixing screws and remove the ware shelf.
3. On the models equipped with the autoradio tape recorder turn out two fixing screws, take the radio tape recorder from the dashboard and disconnect an electrical wiring and an antenna cable from its back part.
4. Turn out four screws and remove a radio tape recorder casing. At the corresponding complete set disconnect an electrical wiring and an antenna cable from a casing.
5. For the purpose of ensuring access to the top driving cables of assembly of management, release clamps and uncover assembly of management.
6. Access to the lower cables opens after an otpuskaniye of screw fixture and extraction of the control panel from the dashboard.
7. For removal of cables release srezny clamps and disconnect tips of cables of control levers.
8. To disconnect a cable tip from the heater block, get under the dashboard (in case of need remove the lower sections of the panel) and disconnect cables, working as it is described above.
9. Try to remember routes of laying of the removed cables.

1. Remove assembly of the dashboard (address the Head Kuzov and finishing of salon).

2. Turn out four screws of fastening of the directing electrical wiring casing to a casing of a heater and an arm of a steering column.

3. Give two top nuts of fastening of the right assembly bracket of the dashboard to an arm of a steering column.

4. Turn out the lower bolt of fastening of the right assembly bracket of the dashboard to a floor, then release an electrical wiring from an assembly bracket.

5. Remove a bracket.

6. Disconnect an electrical wiring from an electric motor of the fan of a heater, its resistor and the control panel of a heater. Release a plait from intermediate clamps on assembly of a heater.

7. Release clamps and uncover the top part of the control panel of functioning of a heater. Disconnect an electrical wiring from illumination lamps.
8. Empty the cooling system (address the Head Routine maintenance).
9. In a motive compartment, as necessary, uncover the camshaft (see the Head Remont of the engine) for the purpose of ensuring access to the hose socket of the heat exchanger of a heater on a back partition.
10. Where it is required, release a metal clip in the top part of the socket.
11. Release a clamp, having wrung out it to the left (see the Detachment and replacement of hoses of the cooling system).

12. Turn out two screws of fastening of a facing level of the hose socket to a partition of a motive compartment.

13. Remove a facing level together with a sealant.

14. In a motive compartment give a bolt and two nuts of fastening of assembly of a heater to a partition (do not forget about washers).

15. In salon remove assembly of a heater and disconnect from it an air duct. Prepare for collecting the spilled cooling liquid.

Not to soil a carpet, cover a floor of salon with a polyethylene film.

16. Having dismantled assembly of a heater, remove a level of fastening of branch pipes with a foam sealant, then release four clamps and take the heat exchanger from assembly of a heater.

1. Release fixing clamps / turn out screws and remove the carpet panel of finishing under the dashboard from the passenger party of the car.

2. Give three fixing screws, then omit assembly of an electric motor and disconnect from it an electrical wiring.

3. Now the motor can be separated from a krylchatka by a reversing of two fixing screws.

1. Release fixing clamps / turn out screws and remove the carpet panel of finishing under the dashboard from the passenger party of the car.
2. The resistor is installed in the heater casing basis, near a driving electric motor of the fan.

3. Turn the basis of resistive assembly, separate it from a casing of a heater and disconnect an electrical wiring.